 |
|
 |
Begin OCR Text:
2. __açe _he ba__ jojnt in pogition on the Steering
knuCkle and fit the clamping bolt.
3. _onneç_ the upper wishbone to the ball joint _
and fit the attach_ng bolts.
q. fit the whee_ and sCrew on the wheel nUtS. _
_ower the vehiçle and final-tighten the Wheel
nuts. 3
2
_OWE_ _A__ JOlNT _
_E_OVIN_
1. __açken the wheel nutS SeVeral tUrns. _ d __C.II__J
2. ffaige the front end and p_aCe a treSt g Un er '''__'
the _ower wighbone. UnsCrew the Wheel nutS
and take down the whee_. Flg. 6_26. LDwer ball ioint att8_hment
u h (6 F 6 26) d th _ Lower b8ll _oint 7. Br8cket
3 ngçreW t e nUtS Ig - an remOVe e _ d g g _
' ' ' 2 PIn _e Ot
four bo_tS (8). ffemove the nut (3). 3 Castle nut 9. Circlip
h F h 4 _plit p_n 1O. Rubber couer
4. DisConneCt the brake OSeS rO__ t e feta_ner_ _. _owe_ w_ghbone 11 Circ1ip
_it too_ _\/_ ___1 _o the gteerin_ knuçk_e, gee 6 NUt
'Fig. 6-'25U.
'PUrokbkaUbly' the retainerYfor the brake
lines may have to be bent Slightly to the one
side. Turn the tool nut until the tool starts to F___N_
t _ __ t t_ _ t__ t_ _ __ _ _ t
enSlOn. Inen Urn ne nU_ Un Il ne Dall )Oln
re_eageS but maK _ 1/2 turng _F the ba__ )_o__nt 1. _heçk to make gure the rubber Seal iS not da-
._g go SeC'ure_y F_tte'd that ._t çann' ot be g_açkened maged and fil_ with grease. _f neCeSSary, flll
w__t_ t___g turn__ng try tapping ___g_t tapg w_jt_ a with univerga_ gre3se. _ake gure that the SleeUe
ham_me_r and C'ounterho_d o'n
_the gteer___ng and _oçk ringg take up the_r proper poSition. See
_nuC__e_g _a_j)o__nt attaC_ment. flg. 6-26.
_
_'
U
'
_ 2. fit the ba__ joint in pogition on the Steering ,
knuçk_e and fit the nut. Tighten the nUt to a
torqUe of 4.8-5.5 kpm (35_O _b.ft.).
3. _onneCt the lower ba__ jointto the WiShbOne and
fit the four attaching bolts.
4. f_t the brake hoses and b_eed the brake Caliper.
5. Fit the whee_ and wheeI nuts. LoWef the uehiCle
and final-tighten the wheel nUtS. fit the hUb
Cap.
U__E_ Wl_H_ONE
_E_LA__N_ _U_HE_
t. _lacken the wheel nutS Several tUrnS.
2. ffaige the front end and plaCe a treStle under
the lower wishbone. Unscrew the wheel nuts
and lift off the wheel.
3. Unscrew the nuts (6, Fjg. 6-13) and remove the
C_ampS (4).
4. _end up the Ioçk plate (3, fig. 6-7). unsCfew
the attaching bolts (2) and remove the shaft.
o Take care of the shims (1).
V'''_''_'_ 5. Remove the nuts (Fig. 6-13). the washers (2). the
Fig. 6-Z_. Removing lower ball joint buSheS (3) and the SleeVeS (5).
6. 14
|
