 |
|
 |
Begin OCR Text:
P 1 2O, P 18OO
_ E _ A _ _ _ _ _ _ _ U _ _ _ O _._
WORK WH l C H CA_ _E CARR_ ED O U_ tfe strainer ín petrol or wfite spirit. Blow dry
w__H ovERDR_vE u___ F___ED with compressed air.
2_ Check that the gasket (3) is in good condition.
CheEking the oil pressure Turn the steel-covered side oi the gasket to
_ . D_ge,gage ihe ove,d,_,,e _,, ,,d,, io ,,m,,, face the housing and place it in position.
any residual oil pressure (late production). o, 3_ PlaCe the three magnetic washers together
early production it may be neceggay io _ (late production) so that they are held together
engage and disengage tfe ove,d,ive _ o-_ 2 by magnetic attraction.
fimes in order to do this. 4. Fit the oil strainer (1 ), magnetic wagherg (2),
2. Remove the plug over the çontrol va_ve a,d a new 9asket (4) and the cover (5).
connect oil pressure gauge SVO 241 5, see
_ Fig_ 8, N, B, The spring (49), tappet <52) and CheEkíng ond odiusting the Eontrol vo_ve
ball (53) should remain in position. _ . _a,k up the ,,f,_,_, a,d p_,,, b_,,k, ,,d,, ih,
3_ Start and drive the car. (The test can also be front and rear aKles.
done with the car jacked up). At a speed of 2. Remove the ,,,,, o,,, if, ,,,t,,_ ,,_,, ,,m.
5O-6O km_p_h. (31 -37 m.p.h.) on overdrive, the Engage the o,e,d,_,ve (w_,th ihe e,g_,,e giopped
_ pressure gauge shou Id show a reading of and Qih sp,,d ,,g,g,d). _f tf, ,,,t,,_ ,,_,,
35-4O kg/'cm' (5OO-57O Ib 'sq.in.) (early pro- ,g co,,e,t_y ad)_ugted, _,i ghou_d be pogg__b_g to
ducfio, 33_3g kg , ,m2 (47O_54O lb. /gq.i,.). lf push a 4.75 mm (_ ,_6,.) d._ameie, p._n ih,ougf the
the pressure gauge shows too low a reading, fo_e ;, th, ,,m ' a,d _,,io th, fo,,_,,g, g,,
See Under '' FaUlt tracing'' concerning the F_g. _ o. lf ,oi, adj_u,i u,t_,l ihe ,o,,ect pog__i_,on
reason and remedy. of ife a,m ,g obta_,ned.
Cl . h .l t . 3, Check tfe current th rough the solenoid wiih
eOning t e O_ _ foinef ihe ,,,,d,_,,, ,,g,g,d. ih, ,, ,,,,i ,ho,ld b,
The oil strainer should be cIeaned at every oi l _aK. 1 A with a 1 2 v gystem and mgK. 2 A wjih _
Change_ First drain off the oil by removing the a 6 V system. _f the current ig _ o-_ 2 A o,
Plug C3, Fig_ 4_ marked '' Drain'') under the oi l higher, this means thaf the sole,ojd a,maiu,g
Stráner. Cleaning shoutd then be done as follows _ _ _ 3
1 _ Remove the cover (5, Fig . 9). Take out the oi l
_
strainer (1 ) and the magnetic w8shers (2). Clean
_
_ 6 f i vr_,_v, u,
Fig_ 9. Removing the oil strainer
1 . Oi I strainer 4. Gasket for _ove,
vo, vo 2. Magnetic washers 5. Couer
''' (late production) 6 Bolts
Fig_ $_ _hec_ing the oiI pr$ssure 3. G8sket for oil stra_ner 4- 3
|
